Original: $45.11
-65%$45.11
$15.79The Story
Bullnose primed MDF window board 250mm wide is designed to finish internal window reveals cleanly and neatly. The rounded front edge gives a safe, modern profile, and two factory-applied white primer coats mean it is ready for a final top coat straight from the pack. Available in 3.6m lengths.
Specifications
| Material | MDF (moisture resistant) |
|---|---|
| Finish | White primed, two coats factory applied |
| Nominal Width | 250mm |
| Length | 3.6m (3600mm / 12ft) |
| Profile | Bullnose front edge |
| Use | Internal only |
What it's used for
- Finishing internal window reveals as a neat, flat surface below the window sash
- Replacing damaged or rotten timber window boards in kitchens and bathrooms where humidity is a concern
- New-build and renovation projects where a consistent, knot-free surface is needed before painting
- Wider-than-standard reveals where a 250mm board is required to span the full depth of the recess
Fitting and handling
Allow the board to acclimatise inside the building for at least 24 hours before fixing, keeping it flat and off the floor to prevent any moisture uptake from the subfloor. Most installers fix using a full-coverage instant-grab adhesive applied to the reveal, with mechanical fixings through the back edge where additional support is needed. Once fitted, apply one or two coats of water-based or oil-based interior paint directly over the factory primer, paying attention to the underside and any cut ends to seal the board fully.
FAQ
Is this window board suitable for use in a kitchen or bathroom?
Yes. It is made from moisture resistant MDF, which resists the swelling and warping that can affect solid timber in humid rooms. It is not waterproof, however, so all cut ends and the underside should be sealed with paint or primer before installation.
Can I cut this window board down to a shorter length on site?
Yes. Moisture resistant MDF cuts cleanly with a circular saw, jigsaw, or hand saw. After cutting, seal the exposed end grain with a coat of primer before fitting to maintain the board's resistance to moisture.
Does this board need sanding before painting?
Light sanding with 180-grit paper will improve adhesion and remove any minor surface marks from transit. Wipe away dust before applying your chosen top coat. No additional primer should be needed on the flat faces, though cut ends must be primed.
Nottage Timber Merchants supplies a full range of pine mouldings and interior mouldings to complement this window board, including skirting, architrave, and ovolo profiles. Next-day delivery is available to Bridgend and across South Wales - contact us for trade account enquiries.
Description
Bullnose primed MDF window board 250mm wide is designed to finish internal window reveals cleanly and neatly. The rounded front edge gives a safe, modern profile, and two factory-applied white primer coats mean it is ready for a final top coat straight from the pack. Available in 3.6m lengths.
Specifications
| Material | MDF (moisture resistant) |
|---|---|
| Finish | White primed, two coats factory applied |
| Nominal Width | 250mm |
| Length | 3.6m (3600mm / 12ft) |
| Profile | Bullnose front edge |
| Use | Internal only |
What it's used for
- Finishing internal window reveals as a neat, flat surface below the window sash
- Replacing damaged or rotten timber window boards in kitchens and bathrooms where humidity is a concern
- New-build and renovation projects where a consistent, knot-free surface is needed before painting
- Wider-than-standard reveals where a 250mm board is required to span the full depth of the recess
Fitting and handling
Allow the board to acclimatise inside the building for at least 24 hours before fixing, keeping it flat and off the floor to prevent any moisture uptake from the subfloor. Most installers fix using a full-coverage instant-grab adhesive applied to the reveal, with mechanical fixings through the back edge where additional support is needed. Once fitted, apply one or two coats of water-based or oil-based interior paint directly over the factory primer, paying attention to the underside and any cut ends to seal the board fully.
FAQ
Is this window board suitable for use in a kitchen or bathroom?
Yes. It is made from moisture resistant MDF, which resists the swelling and warping that can affect solid timber in humid rooms. It is not waterproof, however, so all cut ends and the underside should be sealed with paint or primer before installation.
Can I cut this window board down to a shorter length on site?
Yes. Moisture resistant MDF cuts cleanly with a circular saw, jigsaw, or hand saw. After cutting, seal the exposed end grain with a coat of primer before fitting to maintain the board's resistance to moisture.
Does this board need sanding before painting?
Light sanding with 180-grit paper will improve adhesion and remove any minor surface marks from transit. Wipe away dust before applying your chosen top coat. No additional primer should be needed on the flat faces, though cut ends must be primed.
Nottage Timber Merchants supplies a full range of pine mouldings and interior mouldings to complement this window board, including skirting, architrave, and ovolo profiles. Next-day delivery is available to Bridgend and across South Wales - contact us for trade account enquiries.